전체상품목록 바로가기

본문 바로가기


현재 위치
  1. 게시판
  2. 자료실-통신관련

자료실-통신관련

광통신,시리얼통신,무선통신 및 네트웍통신관련 자료실입니다.

게시판 상세
제목 광모듈에서 CDR (Clock Data Recovery) 사용하는 이유
작성자 엑사통신 (ip:)
  • 평점 0점  
  • 작성일 2018-08-01 12:21:35
  • 추천 추천하기
  • 조회수 1248

광모듈에서 CDR (Clock Data Recovery) 사용하는 이유


What do I use a CDR for?


Physical impacts are influencing the optical signal during the transmission over fiber optic cables. Due to the length of an optical link the signal suffers a time delay deviation which leads to problems in synchronization. In addition an optical fiber attenuates the signal which leads to a degradation of the signal. The physical impacts are linear and non-linear effects which are leading to wave distortion.


This is why a 3R-regeneration will be used:
1. Re-Amplification (regeneration of amplitude)
2. Re-Shaping (regeneration of signal waveform)
3. Re-Timing (regeneration of synchronization)

The transceiver includes a Limiting Amplifier (*1), which compensates step 1 & 2 at receiver side. For step 3 (Re-Timing) there is an additional CDR chip set integrated in the transceiver.


When do I have to use a transceiver with CDR?


This question was raised with the introduction of SFP+ modules.

Short summary:
XFP modules are built with CDR on-board as defined in the related MSA-Standard.
To realize a cost effective and smaller form-factor this functionality doesn't become part of the SFP+ module.

The idea was implementing CDR directly in the host-system of the SFP+ if needed.
This would increase the price of the end-devices like switches and routers.
A 2R-regeneration (Re-Amplification, Re-Shaping) is already part of the transceiver so it is not mandatory to implement a CDR function.


To realize a standard link this is usually sufficient. Standard links are typically in-house wiring (Multimode), 10km, 20km and 40km point-to-point connections.
But if you are planning to set up a wavelength multiplexing (DWDM), an optical amplifier or transmitting over long distances, you should consider a complete 3R-regeneration. This can be achieved with a CDR chip set either in your DWDM-transponder, host-system or transceiver. Most of the DWDM transponder-systems do have a CDR functionality on board.



Which advantages come with a CDR?


There are a lot of effects on an amplified DWDM link which have a lot of impact on the transmission signal. For an error-free detection parameters like:


ONSR (Optical signal-to-noise ratio)
BER (Bit-error-ratio)
Input power value
Data rate
Degradation of the signal


have impact on each other. A stable reliable DWDM link can be achieved, if you take the first four points into consideration by planning an amplified DWDM link and in addition eliminating the last point by using a 3R-regeneration with CDR.


첨부파일
비밀번호 수정 및 삭제하려면 비밀번호를 입력하세요.
관리자게시 게시안함 스팸신고 스팸해제 목록 삭제 수정 답변
댓글 수정

비밀번호 :

수정 취소

/ byte

비밀번호 : 확인 취소

댓글 입력
댓글달기 이름 : 비밀번호 : 관리자답변보기

영문 대소문자/숫자/특수문자 중 2가지 이상 조합, 10자~16자

확인

/ byte

왼쪽의 문자를 공백없이 입력하세요.(대소문자구분)

관리자에게만 댓글 작성 권한이 있습니다.



장바구니 0
 

WORLD SHIPPING

PLEASE SELECT THE DESTINATION COUNTRY AND LANGUAGE :

GO
close